Name: Pro-Tech - Beading Bit 5/16 X 3/8 Plunge Cutting 1/2 Shank - Pro-Tech - Beading Bit 5/16 X 3/...
SKU: 24207669
Price: 299.00 ZAR
Availability: InStock

Pro-Tech - Beading Bit 5/16' X 3/8' Plunge Cutting 1/2' Shank - Pro-Tech - Beading Bit 5/16' X 3/...

New

35 available

Indicative market price: R489.00

R299.00

39% off

Shipping

R35.00 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30.00 surcharge. This will be calculated at checkout if applicable.
Check my rate

The seller allows collection for this item. Buyers will receive the collection address and time once the order is ready.

The seller has indicated that they will usually have this item ready to ship within 3 business days. Shipping time depends on your delivery address. The most accurate delivery time will be calculated at checkout, but in general, the following shipping times apply:

Standard Delivery

Main centres:	1-3 business days
Regional areas:	3-4 business days
Remote areas:	3-5 business days

Seller

Toolhome408

84.43 % Positive ratings

Buyer protection

How you're covered

Get it now, pay later

Condition

New

Location

South Africa

Product code

24207669

Bob Shop ID

690235167

Beading router bit

Carbide Tipped

This particular beading bit is a plunge version. Also referred to a plunge profile or plunge form bits. Designed to cut grooves with the edges of the groove displaying a particular profile, in this case a beading profile.

Quarter-round profiles are formed by this bit as it grooves, one on each side of a flat. The scale and depth of the beading profile distinguishes it from the round-over above. Used with a fence or edge guide, this beading bit can be used as an edge former. Mainly used for decorative work.

This router bit has a6,35 mm shank (shaft) that will fit most small routers. Please ensure that you select a router bit with a shank (shaft) size that will fit into your router collet.

PRO-TECH router bits are manufactured in Taiwan.

Features

Beading router bit features

Specifications

Part No.	Shank dia.	Cutting width	Cutting Height	Radius
KP209011	¹/₄ inch	⁵/₁₆ inch	³/₈ inch	¹/₈ inch
KP209011	6.35 mm	7.94 mm	9.53 mm	3.18 mm

Length of Shank: 38 mm

Core box bit

Safety

consider safety for your health and the people around you
General safety suggestions: It is advisable to always have the following items nearby and in a good condition Eye protection clean and scratch free Hearing protection quality earmuffs Dust masks discard old and dirty masks Gloves for easy handling of material and hand protection

Wear Gloves	Eye Protection	Hearing Protection	Dust Mask

To use router bits safely (and to get the best results from your router), the router bits need to be installed properly into the router's collet. Improper installation of your bits can cause excessive chatter and could increase the likelihood that the bits will break when in use.

Clean and sharp

First of all, before beginning any routing operation, check your bits to make sure that they are clean, relatively free of pitch, and most of all, sharp. If the bit is dull, chipped, is excessively burned or has any other defect, it should be sharpened or replaced before use.

Correct collet and collet nut fit

Most router collets have a recess (groove) that needs to click into a circlip that resides inside the collet nut. Failing to ensure that the collet "clicked" into the collet nut will cause you to struggle to remove the router bit after tightening. This could cause the collet to break or be removed by a technical re

Report a problem