Name: Pro-Tech - Mortising Bit 1/2 X 10mm (Ideal For Hinge Recesses) 1/4 Shank - Pro-Tech - Mortising...
SKU: 24207743
Price: 249.00 ZAR
Availability: InStock

Pro-Tech - Mortising Bit 1/2' X 10mm (Ideal For Hinge Recesses) 1/4' Shank - Pro-Tech - Mortising...

New

18 available

Indicative market price: R409.00

R249.00

39% off

Shipping

R35.00 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30.00 surcharge. This will be calculated at checkout if applicable.
Check my rate

The seller allows collection for this item. Buyers will receive the collection address and time once the order is ready.

The seller has indicated that they will usually have this item ready to ship within 3 business days. Shipping time depends on your delivery address. The most accurate delivery time will be calculated at checkout, but in general, the following shipping times apply:

Standard Delivery

Main centres:	1-3 business days
Regional areas:	3-4 business days
Remote areas:	3-5 business days

Seller

Toolhome408

84.43 % Positive ratings

Buyer protection

How you're covered

Get it now, pay later

Condition

New

Location

South Africa

Product code

24207743

Bob Shop ID

690376715

Two flute Metric Straight bit

Carbide Tipped

This bit is used for cutting shallow mortises for hinges and locksets. Its cutting geometry is calculated to produce an exceptionally clean cut with crisp edges. A proper mortising bit, as pictured, should have a large gullet between the two flutes.

Carbide tipped cutting edges feature outstanding cutting tool longevity and performance. Pro-Tech router bits cut through a variety of materials from wood, plywood, MDF and other wood composites, plastics, and solid surfaces.

Use a two-flute bit where fine finish is paramount. Two flutes balance the bit, eliminating vibration that degrades the cut finish.

Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced.

This router bit has a6.35mm shank (shaft) that will fit most small routers. Please ensure that you select a router bit with a shank (shaft) size that will fit into your router collet.

PRO-TECH router bits are manufactured in Taiwan.

Features

Features and descriptions

Specifications

Part No.	Shank dia.	Cutting width	Cutting Height	Radius (r)
KP3301	¹/₄ in ( 6.35mm )	¹/₂ in 12,7 mm	10 mm	Straight

Length of Shank: 32 mm

Straight bit, 2 Flute, TCT - 10,00 mm cutting width

Mortising profile

Safety

consider safety for your health and the people around you
General safety suggestions: It is advisable to always have the following items nearby and in a good condition Eye protection clean and scratch free Hearing protection quality earmuffs Dust masks discard old and dirty masks Gloves for easy handling of material and hand protection

Wear Gloves	Eye Protection	Hearing Protection	Dust Mask

To use router bits safely (and to get the best results from your router), the router bits need to be installed properly into the router's collet. Improper installation of your bits can cause excessive chatter and could increase the likelihood that the bits will break when in use.

Clean and sharp

First of all, before beginning any routing operation, check your bits to make sure that they are clean, relatively free of pitch, and most of all, sharp. If the bit is dull, chipped, is excessively burned or has any other defect, it should be sharpened or replaced before use.

Correct collet and collet nut fit

Most router collets have a recess (groove) that needs to click into a circlip that resides inside the collet nut. Failing to ensure that the collet "clicked" into the collet nut will cause you to struggle to remove the router bit after tightening. This could cause the collet to break or be removed by a technical repair centre.

Report a problem