RF Nano V3.0 Micro USB Module ATmega328P QFN32 5V 16M CH340 Integrate NRF24l01+2.4G Wireless Imme
New
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 15 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Returns
Get it now, pay later
Seller
Buyer Protection
Product details
Condition
New
Location
International
Bob Shop ID
615100277
Feature: ? 1. Creative products, RF-Nano-Board: Upgraded nano board for , The main chip is ATMEGA328P-MU QFN32, the latest bootloader ( IDE 1.8.8) was burned down. It is fully compatible with the common nano board. RF-Nano-Board is PIN-PIN with Nano V3.0,and share the same codes. 2. More convenient for application: The RF-Nano-Board integrates an NRF24L01+ module with nano v3.0 board, which is very convenient for 2.4G wireless connect application. 3. High quality material and Technology: We used high quality PCB original material and Immersion Gold Technology to make sure every board has smooth edge and more reliable. 4. Super small volume design, more convenient to use: The PCB size is only 48mm*19mm, the pin is fully compatible with Nano V3.0,No Soldering needed. The micro usb port is more convenient to use. 5. RF-Nano-Board using CH340 chip to UART, you can download mac, windows, Linux three system drivers. ? Specification: ? Microcontroller ATmega328P Nrf24L01+ 2.4G wireless Architecture AVR Operating Voltage: 5 V Flash Memory: 32 KB of which 2 KB used by bootloader SRAM: 2 KB Clock Speed: 16 MHz Analog I/O Pins: 8 EEPROM: 1 KB DC Current per I/O Pins: 40 mA (I/O Pins) Input Voltage: 7-12 V Digital I/O Pins: 22 PWM Output: 6 Power Consumption: 19 mA Weight: 9g
Parameter: ? a?? It is fully compatible with the nano-v3.0 pin and its usage method a?? BLE chip: TI CC2540 a?? Work channel: 2.4G a?? Transmission distance: 50m a?? Supports AT directive to configure BLE a?? Support USB virtual serial port, hardware serial port, BLE three-way transparent transmission a?? Support master and slave switch a?? Supports sending over 20byte. a?? Supports iBeacons a?? Interface: Micro-USB a?? Input voltage: USB power supply, Vin6~12V, 5V a?? MCU: ATmega328P-MU QFN32 a?? Bootloader: Newest 1.8.8 a?? Pin: Two Lines 2.54mm-15Pin a?? Size: 48mm x 19mm x 12mm ? Package includes:? ? 1 x RF Nano board ? Note:
Please use IDE 1.8.6 or higher version, First, install the CH340 driver, then follow this selection path in IDE: Tools - ?Boarda?? Nanoa?? Processor a??ATmega328P, otherwise you'll find that you can't burn any program.?
Parameter: ? a?? It is fully compatible with the nano-v3.0 pin and its usage method a?? BLE chip: TI CC2540 a?? Work channel: 2.4G a?? Transmission distance: 50m a?? Supports AT directive to configure BLE a?? Support USB virtual serial port, hardware serial port, BLE three-way transparent transmission a?? Support master and slave switch a?? Supports sending over 20byte. a?? Supports iBeacons a?? Interface: Micro-USB a?? Input voltage: USB power supply, Vin6~12V, 5V a?? MCU: ATmega328P-MU QFN32 a?? Bootloader: Newest 1.8.8 a?? Pin: Two Lines 2.54mm-15Pin a?? Size: 48mm x 19mm x 12mm ? Package includes:? ? 1 x RF Nano board ? Note:
Please use IDE 1.8.6 or higher version, First, install the CH340 driver, then follow this selection path in IDE: Tools - ?Boarda?? Nanoa?? Processor a??ATmega328P, otherwise you'll find that you can't burn any program.?