Seeed Studio (106990020) Solar Charger Shield, 3W Output, 3 V to 4.5 V Seeed Studio (106990020) Solar Charger Shield, 3W Output, 3 V to 4.5 V Seeed Studio (106990020) Solar Charger Shield, 3W Output, 3 V to 4.5 V Seeed Studio (106990020) Solar Charger Shield, 3W Output, 3 V to 4.5 V Seeed Studio (106990020) Solar Charger Shield, 3W Output, 3 V to 4.5 V
Seeed Studio (106990020) Solar Charger Shield, 3W Output, 3 V to 4.5 V Seeed Studio (106990020) Solar Charger Shield, 3W Output, 3 V to 4.5 V Seeed Studio (106990020) Solar Charger Shield, 3W Output, 3 V to 4.5 V Seeed Studio (106990020) Solar Charger Shield, 3W Output, 3 V to 4.5 V Seeed Studio (106990020) Solar Charger Shield, 3W Output, 3 V to 4.5 V

Seeed Studio (106990020) Solar Charger Shield, 3W Output, 3 V to 4.5 V

New 53 available
R819.00
Shipping
R35.00 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30.00 surcharge. This will be calculated at checkout if applicable.
Check my rate
The seller allows collection for this item. Buyers will receive the collection address and time once the order is ready.
The seller has indicated that they will usually have this item ready to ship within 3 business days. Shipping time depends on your delivery address. The most accurate delivery time will be calculated at checkout, but in general, the following shipping times apply:
 
Standard Delivery
Main centres:  1-3 business days
Regional areas: 3-4 business days
Remote areas: 3-5 business days
Seller
Buyer protection
Get it now, pay later

Product details

Condition
New
Location
South Africa
Product code
4060369
Bob Shop ID
645130448
The V2.2 Solar Charger is a stackable shield to Arduino compatible platforms,enables adaptive battery power and act as energy harvester for in-fieldcharging. You may use various batteries that has the voltage of 3.0V-4.2V toshift up for 5V output, or put on Li-ion battery and solar panel to form anautonomous sensor unit. The maximum current provided by the board can get up to600mA. An USB connector is also useful to charge the battery.Specifications:- Short circuit protection- 3W output power when connecting battery- Continuous charge current up to 900mA- Battery status indication ( red : charging , green: charged )- Micro-USB connector- USB input voltage range from 4.75 to 5.25V, solar input voltage range from 4.8to 6V- Ripple voltage is 100mV at 500mA- Dimension is 68 x 53mm- For use with: Arduino Board- Kit contents: Solar Charger Shield V2.2 Board
Add to cart

Recently viewed

Texas Instruments (SN65LVDS94DGG) SerDes, Serialiser / Deserialiser
New
R575.00
Tt Electronics (OPB620) Transmissive Photo Interrupter, Phototransistor
New
R189.00

Similar products

Seeed Studio (101020555) Thermocouple Amplifier Board, 1 Wire, 3.3 V / 5 V
New
R839.00
Seeed Studio (105020011) Haptic Motor Module, 3.3V to 5V, 750 mW
New
R779.00
Seeed Studio (111020048) Switch Board, with Cable, 5 Ways, 3.3V / 5V
New
R269.00
Seeed Studio (101020089) Sunlight Sensor, With Cable, 3 V to 5.5 V
New
R675.00