Servo Driver HAT (B) Servo Drive Board Right Angle Pinheader for Raspberry Pi 16-Channel 12-bit I2C Servo Driver HAT (B) Servo Drive Board Right Angle Pinheader for Raspberry Pi 16-Channel 12-bit I2C Servo Driver HAT (B) Servo Drive Board Right Angle Pinheader for Raspberry Pi 16-Channel 12-bit I2C
Servo Driver HAT (B) Servo Drive Board Right Angle Pinheader for Raspberry Pi 16-Channel 12-bit I2C Servo Driver HAT (B) Servo Drive Board Right Angle Pinheader for Raspberry Pi 16-Channel 12-bit I2C Servo Driver HAT (B) Servo Drive Board Right Angle Pinheader for Raspberry Pi 16-Channel 12-bit I2C

Servo Driver HAT (B) Servo Drive Board Right Angle Pinheader for Raspberry Pi 16-Channel 12-bit I2C

20 available / new
R670.00
Shipping
R35.00 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30.00 surcharge. This will be calculated at checkout if applicable.
Check my rate
The seller has indicated that they will usually have this item ready to ship within 12 business days. Shipping time depends on your delivery address. The most accurate delivery time will be calculated at checkout, but in general, the following shipping times apply:
 
Standard Delivery
Main centres:  1-3 business days
Regional areas: 3-4 business days
Remote areas: 3-5 business days
Seller
Buyer protection
Returns
Replacement Guarantee: 7 Days: We stand by this guarantee
Get it now, pay later

Product details

Condition
New
Location
International
Bob Shop ID
645884666
.size_table_start table,.size_table_start table tr td { border:2px solid #ddd;}.size_table_start table { width: 100%; min-height: 25px; line-height: 25px; text-align: center; border-collapse: collapse;}.size_table_start,.size_table_end {clear:both;}

Features:

Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards, Jetson Nano
I2C controlled, using only 2 pins
Up to 16-Channel servo/PWM outputs, 12-bit resolution for each channel (4096 scales)
Integrates 5V regulator, up to 3A output current, can be powered from battery through VIN terminal
Standard servo interface, supports common used servo such as SG90, MG90S, MG996R, etc.
Reserved I2C control pins, allows to work with other control boards
Comes with development resources and manual (examples in python like Bluetooth/WiFi remote control)
a
aResources:




a
Specifications:

Power supply: 5V (Pi connector) OR 6V~12V (VIN terminal)
Servo voltage: 5V
Logic voltage: 3.3V
Driver: PCA9685
Control interface: I2C
Dimension: 65mm x 30mm
Mounting hole size: 3.0mm

Supported Servo:
This HAT can be used to drive servos such as:
SG90 Servo
MG90S Servo
MG996R Servo
a
aOrdering Info:
This HAT provides 2 options for the onboard pinheader:
Servo Driver HAT (B): right angle pinheader, make it possible to connect servos even when stacking up
a
aPackage Included:
a

Note: Raspberry Pi and servos are NOT included.
a
aServo Driver HAT (B) x1
aRPi screws pack (2pcs) x1



Add to cart

Recently viewed

See more
PORT NUMERIC KEYPAD WIRED - TYPE C
R450.00
PH Value Data Detection and Acquisition Sensor Module Acidity and Alkalinity Se... (TYPE: WITHPROBE)
R697.00
9% OFF
Kitronik Discovery Kit for Raspberry Pi Pico (Pico not included)
R289.88 R318.87

Similar products

Raspberry Pi 4B Development Board Cooling Fan Suitable for RaspberryPi Turbo Fan with L... (TYPE: B)
R535.00
9% OFF
Raspberry Pi Sense HAT V2
R811.89 R893.08
Raspberry Pi (RASPBERRY PI PICO W) Board, 32bit, ARM Cortex-M0+
R365.00
Right Angle Female Header For Raspberry Pi
R18.00