ST-LINK/V2 (mini), STM Programmers & Debuggers
New
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 15 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Get it now, pay later
Seller
Buyer Protection
Product details
Condition
New
Location
International
Product code
ZY14348195
Bob Shop ID
593699379
Description
Mini ST-LINK/V2 on a small single board, an extreme low cost solution for in-circuit debugger/programmer for STM8 and STM32.
Features
1. Onboard 500mA self-recovery fuse to avoid harming by short circuit
2. Dual voltage output (3.3V/5V), easy for debugging/programming
3. Standard USB interface for direct connection to PC
4. Debugging/Programing performance
- Debugging : run at full-speed, single-stepped, breakpoints, viewing variables and registers, etc.
- Programming : supports FLASH ROM, EEPROM, AFR, etc.
- USB2.0 combined with SWIM/SWD interfaces : quick response for debugging & fast speed for programming
5. Upgradable firmware
- The firmware is upgradable to support more devices in the future
- Automatically upgraded
6. Supported software
- ST-LINK Utility v2.0 (or higher ver.)
- STVD Version 4.2.1 (or higher ver.)
- STVP Version 3.2.3 (or higher ver.)
- IAR EWARM Revision v6.20 (or higher ver.)
- IAR EWSTM8 Revision v1.30 (or higher ver.)
- KEIL RVMDK Revision v4.21 (or higher ver.)
- ATOLLIC
- TASKING
7. Supported devices
- All the STM8 devices with SWIM interface
- All the STM32 devices with SWD interface
Package Contents
1. ST-LINK/V2 (mini) 1
2. 4-pin custom connector cable 1
3. USB type A plug to receptacle cable 1
Mini ST-LINK/V2 on a small single board, an extreme low cost solution for in-circuit debugger/programmer for STM8 and STM32.
Features
1. Onboard 500mA self-recovery fuse to avoid harming by short circuit
2. Dual voltage output (3.3V/5V), easy for debugging/programming
3. Standard USB interface for direct connection to PC
4. Debugging/Programing performance
- Debugging : run at full-speed, single-stepped, breakpoints, viewing variables and registers, etc.
- Programming : supports FLASH ROM, EEPROM, AFR, etc.
- USB2.0 combined with SWIM/SWD interfaces : quick response for debugging & fast speed for programming
5. Upgradable firmware
- The firmware is upgradable to support more devices in the future
- Automatically upgraded
6. Supported software
- ST-LINK Utility v2.0 (or higher ver.)
- STVD Version 4.2.1 (or higher ver.)
- STVP Version 3.2.3 (or higher ver.)
- IAR EWARM Revision v6.20 (or higher ver.)
- IAR EWSTM8 Revision v1.30 (or higher ver.)
- KEIL RVMDK Revision v4.21 (or higher ver.)
- ATOLLIC
- TASKING
7. Supported devices
- All the STM8 devices with SWIM interface
- All the STM32 devices with SWD interface
Package Contents
1. ST-LINK/V2 (mini) 1
2. 4-pin custom connector cable 1
3. USB type A plug to receptacle cable 1