STARTRC For DJI Mavic Air 2 / Air 2S Damping Landing Gear Training Floating Kit
New
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 15 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Get it now, pay later
Seller
Buyer Protection
Product details
Condition
New
Location
International
Product code
DOP6201
Bob Shop ID
598097607
1. Various functions, not only can be used as a buoyancy bar, but also can be used as a heightening tripod and landing gear, effectively increasing 60mm
2. Non-destructive installation design, easy to install, can be disassembled and assembled by itself
3. Wear 1/4 adapter, can extend other parts, used with camera, fill light, etc.
4. Lightweight design will not bring a heavy burden to the drone
5. Material: ABS
6. Dimensions: 247x240mm
7. Note: The floating kit allows the drone to land or take off in calm water instead of in rough water, otherwise the drone may be lost
8. Packing list: buoyancy rod main board * 1, buoyancy rod top cover * 1, buoyancy rod * 2, tripod * 4, M3 * 6 * 12 screw * 2, 1/4 * 10 screw * 1, tripod adapter * 1, m5 screw * 1, gasket * 1, electrostatic bag * 1
Installation steps:
1. Place the main installation cover on top of the drone
2. As shown in the figure, fix the four sponge stick mounts on the main mount connection part
3. Turn the drone over, and then align the main mounting bracket with the bottom of the drone
4. Fix the main bracket and the top cover of the main bracket with two M3 screws on the drone
5. Insert the sponge stick into the ring of the main fixing frame, and adjust each stick to the proper balance position
6. After adjustment, place the drone on the water and check the balance. If unbalanced, adjust the position of the sponge stick and balance it back and forth
2. Non-destructive installation design, easy to install, can be disassembled and assembled by itself
3. Wear 1/4 adapter, can extend other parts, used with camera, fill light, etc.
4. Lightweight design will not bring a heavy burden to the drone
5. Material: ABS
6. Dimensions: 247x240mm
7. Note: The floating kit allows the drone to land or take off in calm water instead of in rough water, otherwise the drone may be lost
8. Packing list: buoyancy rod main board * 1, buoyancy rod top cover * 1, buoyancy rod * 2, tripod * 4, M3 * 6 * 12 screw * 2, 1/4 * 10 screw * 1, tripod adapter * 1, m5 screw * 1, gasket * 1, electrostatic bag * 1
Installation steps:
1. Place the main installation cover on top of the drone
2. As shown in the figure, fix the four sponge stick mounts on the main mount connection part
3. Turn the drone over, and then align the main mounting bracket with the bottom of the drone
4. Fix the main bracket and the top cover of the main bracket with two M3 screws on the drone
5. Insert the sponge stick into the ring of the main fixing frame, and adjust each stick to the proper balance position
6. After adjustment, place the drone on the water and check the balance. If unbalanced, adjust the position of the sponge stick and balance it back and forth