This item has closed 2 buyers bought 4 items
View other items offered by Led Select - Cape Town29868

Similar products

D85-3050 DC 0-200V 10A Digital Voltmeter Ammeter LCD Panel Volt Amp Meter Gauge White
R607.00
Voltmeter DC 0-100V 4 Digit Display Adjustable **LOCAL STOCK**
R99.00
D27B DC 33V/10A Voltage/Current Dual Display Meter Digital Voltmeter Ammeter
R518.00
Voltmeter Ammeter DC 0-100V 50A 3 Digit Display Adjustable **LOCAL STOCK**
R109.00
Voltmeter/ Ammeter DC 0.00-33.0V/10A Dual LED Display (Red+Yellow) **IN STOCK**
Sold

Voltmeter/ Ammeter DC 0.00-33.0V/10A Dual LED Display (Red+Yellow) **IN STOCK**

4 were available / new
R98.00
Shipping
R65.00 Standard shipping applies to orders under R100.00, in most areas in South Africa. R35.00 Standard shipping applies to orders over R100.00. Some areas may attract a surcharge surcharge. This will be calculated at checkout if applicable.
Check my rate
The seller allows collection for this item. Buyers will receive the collection address and time once the order is ready.
The seller has indicated that they will usually have this item ready to ship within 2 business days. Shipping time depends on your delivery address. The most accurate delivery time will be calculated at checkout, but in general, the following shipping times apply:
 
Standard Delivery
Main centres:  1-3 business days
Regional areas: 3-4 business days
Remote areas: 3-5 business days
Buyer protection
Get it now, pay later

Product details

Condition
New
Location
South Africa
Customer ratings:
Product code
MET142
Bob Shop ID
306368212

Ammeter Voltmeter DC 0.00-33.0V/10A Dual LED Display (Red+Yellow):

Technical Parameters:

Display Colour: Red+Yellow
Display Mode: Dual 0.28 LED Digital Tube
Update Rate: About 500 ms/time
Physical Size: 48 x 29 x 26 mm (L * W *  H)
Opening Size: 45 x 26 mm (L * W)
Supply Voltage: 3.5-30V
Lead Wire Length: 14 cm (Five wires)
Measurement Range: DC 0.00-9.99A (current) 0.00-33.0V(voltage)
Operation Temperature: -10 Degrees~65 Degrees
Measurement Accuracy: ± (1% + 2 digits)

 

 

Instruction of Wiring:

Red thin wire (VCC): Power input+ 3.5-30V (NOTE: If the measuring signal is lower than 30V and have abundant power supply, it can be used as power supply for the module [black wire and yellow wire are contacted together to use]

Black thin wire(GND): Power input- Measurement signal - 3.5-30V

Yellow thin wire (VIN): Measurement signal+ (0-33.0V)

Red thick wire (I+): Current input+ (connect with load negative) 

Black thin wire(I-): Current input- (in series in power supply negative)

 

Voltage current meter with isolated power supply:


  

Instruction:
 
To Calibrate the meter to zero, when the meter is off the power, please connect A and B. Then give the meter power, the meter will automatically be calibrated to zero. When the automatic calibration is over, please disconnect A and B.
 

 

 

Please see all our listings here:
www.bidorbuy.co.za/seller/434337/Led_Select

Recently viewed

See more
52% OFF
iPhone 8 Plus
R5,259.00 R10,999.00
Steam tank purge solenoid valve 06E906517A For Audi A4 A6 A8 Q7 VW Jetta Passat
R312.00
The Daylight Gate - Jeanette Winterson
R200.00
BZN Gold (MMTCD 2106)
R40.00

Customer ratings: 1 ratings

Fantastic service and prompt delivery
03 Nov 2017