Waterproof DS18B20 Digital temperature sensor Resistor

New
Indicative market price: R66.22
-+
153 available
R60.20
Shipping
Standard courier shipping from R60
R60 Standard shipping applies to orders under R100, in most areas in South Africa. R30 Standard shipping applies to orders over R100. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Free collection from Henley on Klip, Meyerton
The seller allows collection for this item and will be in contact with the full collection address once the order is ready. Ready for collection by Tuesday, 28 May.
Ready to ship in
The seller has indicated that they will usually have this item ready to ship within 2 business days. Shipping time depends on your delivery address. The most accurate delivery time will be calculated at checkout, but in general, the following shipping times apply:
 
Standard Delivery
Main centres:  1-3 business days
Regional areas: 3-4 business days
Remote areas: 3-5 business days
Get it now, pay later
Seller
Buyer Protection

Product details

Condition
New
Location
South Africa
Product code
269
Bob Shop ID
613700870
This is a pre-wired and waterproofed version of the DS18B20 sensor.  Handy for when you need to measure something far away, or in wet  conditions. While the sensor is good up to 125C the cable is jacketed  in PVC so we suggest keeping it under 100C. Because they are digital,  you don't get any signal degradation even over long distances! These  1-wire digital temperature sensors are fairly precise (0.5C over much  of the range) and can give up to 12 bits of precision from the onboard  digital-to-analog converter. They work great with any microcontroller  using a single digital pin, and you can even connect multiple ones to  the same pin, each one has a unique 64-bit ID burned in at the factory  to differentiate them. Usable with 3.0-5.0V systems.

The only  downside is they use the Dallas 1-Wire protocol, which is somewhat  complex, and requires a bunch of code to parse out the communication. If  you want something really simple, and you have an analog input pin,  the TMP36 is trivial to get going.

We toss in a 4.7k resistor, which is required as a pullup from the DATA to VCC line when using the sensor.


Cable specs

  • Stainless steel tube 6mm diameter by 30mm long
  • Cable is 36" long / 91cm, 4mm diameter
  • Contains DS18B20 temperature sensor
  • If  your sensor has four wires - Red connects to 3-5V, Black connects to  ground and White is data. The copper wire is soldered to the wire  shielding
  • If your sensor has three wires - Red connects to 3-5V, Blue/Black connects to ground and Yellow/White is data

DS18B20 Technical specs

  • Usable temperature range: -55 to 125C (-67F to 257F)
  • 9 to 12 bit selectable resolution
  • Uses 1-Wire interface- requires only one digital pin for communication
  • Unique 64 bit ID burned into chip
  • Multiple sensors can share one pin
  • 0.5C Accuracy from -10C to 85C
  • Temperature-limit alarm system
  • Query time is less than 750ms
  • Usable with 3.0V to 5.5V power/data

What's in the box?

1 x DS18B20 Digital temperature sensor
1 x 4.7k resistor

Resources

Adafruit's Raspberry Pi Lesson: DS18B20 Temperature Sensing

 

Note: Stock is currently available in South Africa for national shipping!

More from this seller

View all
9% OFF
Infrared Obstacle Avoidance Sensor
R19.61 R21.57
2.54mm Pitch Single Row Pin Header 40-PIN - Black
R4.52
9% OFF
Clear Acrylic Case With Heatsink For Raspberry Pi Zero and Zero 2
R57.88 R63.67
9% OFF
Interior Panel Mount Temperature Meter - Celsius
R81.08 R89.19
Add to cart

Similar products

60% OFF
Temperature and Relative Humidity Sensor Module for Electronics DIY, Projects and Developments
R37.99 R94
R30 shipping
10PCS TEMPERATURE SENSOR Coolant Water Switch For Toyota 89422-33030 8942233030 89422-0D010 89422...
R1,115
R30 shipping
DSA2 2x D/A converter DS18B20 to 0-10V
R4,256
Temperature sensor on PCB - Thermistor NTC Sensors
R65.24