Waveshare 2.13 Inch E-ink Screen Display e-Paper Module SPI Interface Partial Refresh Black Yellow
New
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 15 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Buyer Protection
How you're covered
Get it now, pay later
Returns
Product information
Condition:
New
Location:
International
Bob Shop ID:
612369637
Documents:
Overview:
This is an E-Ink display HAT, 2.13inch, 212x104 resolution, with embedded controller, communicating via SPI interface, supports yellow, black, and white three-color display. Due to the advantages like ultra low power consumption, wide viewing angle, clear display without electricity, it is an ideal choice for applications such as shelf label, industrial instrument, and so on.
Features:
No backlight, keeps displaying last content for a long time even when power down Ultra low power consumption, basically power is only required for refreshing Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards, Jetson Nano SPI interface, for connecting with other controller boards like Arduino/Nucleo, etc.
Specifications:
Operating voltage: 3.3V/5V Interface: 3-wire SPI, 4-wire SPI Outline dimension: 65mm ?? 30.2mm Display size: 23.71mm ?? 48.55mm Dot pitch: 0.229 ?? 0.228 Resolution: 212 ?? 104 Display color: Yellow, black, white Grey level: 2 Full refresh time: 15s Refresh power: 26.4mW(typ.) Standby power: <0.017mW Viewing angle: >170?ﾣ
Interface:
Package includes: (the expansion board is not includes)
1 x?2.13inch e-Paper HAT (C)
Overview:
This is an E-Ink display HAT, 2.13inch, 212x104 resolution, with embedded controller, communicating via SPI interface, supports yellow, black, and white three-color display. Due to the advantages like ultra low power consumption, wide viewing angle, clear display without electricity, it is an ideal choice for applications such as shelf label, industrial instrument, and so on.
Features:
No backlight, keeps displaying last content for a long time even when power down Ultra low power consumption, basically power is only required for refreshing Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards, Jetson Nano SPI interface, for connecting with other controller boards like Arduino/Nucleo, etc.
Specifications:
Operating voltage: 3.3V/5V Interface: 3-wire SPI, 4-wire SPI Outline dimension: 65mm ?? 30.2mm Display size: 23.71mm ?? 48.55mm Dot pitch: 0.229 ?? 0.228 Resolution: 212 ?? 104 Display color: Yellow, black, white Grey level: 2 Full refresh time: 15s Refresh power: 26.4mW(typ.) Standby power: <0.017mW Viewing angle: >170?ﾣ
Interface:
| SYMBOL | DESCRIPTION |
| VCC | 3.3V/5V |
| GND | Ground |
| NC | NC |
| DIN | SPI MOSI pin |
| CLK | SPI SCK pin |
| CS | SPI chip selection, low active |
| DC | Data/Command selection (high for data, low for command) |
| RST | External reset, low active |
| BUSY | Busy status output, low active |
Package includes: (the expansion board is not includes)
1 x?2.13inch e-Paper HAT (C)
