WUPP CS-095D1 Motorcycle Modified Adjustable Temperature Silicone Universal Electric Heating Hand...
New
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 15 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Get it now, pay later
Seller
Buyer Protection
Product details
Condition
New
Location
International
Product code
MOTA4650B
Bob Shop ID
593706075
1. 2V voltage, 22MM handlebar inner diameter, suitable for most motorcycles
2. The product is equipped with high and low gear switches, and the handle temperature can be adjusted at will (50-70 degrees Celsius adjustable)
3. Double throttle cable buckle, wider installation range
4. The design can be sealed and can be opened, which will not affect the installation of the handle outside the handle, and then the lights and other decorative accessories are more beautiful and convenient
5. Input voltage: 12V
6. Power: 15W-35W adjustable
7. Length: left hand handle 143x36mm; right hand handle 127x36mm
Installation notes:
1. Remove the original handlebar
2. Use the left hand to moisten the inner hole with soapy water, and the twist should not be too large during installation
3. When installing the balance iron on the left hand handle, adjust the position of the balance iron to be slightly separated from the handle, and do not squeeze the handle when tightening the screw
4. If you use the left handle to slide on a steel pipe, remove the balance iron, and fix it with a few drops of 502 glue from the end of the handle
5. The power cord, the red wire is connected to the positive pole, and the black wire is connected to the negative pole, the temperature cannot be adjusted when reverse connection
6. When installing the left-hand handle, the power cord should be left enough for rotation
Precautions:
1. When installing the left handle, do not twist the handle too much. Excessive twisting will cause the heating wire to shift
2. For models with balance iron, please adjust the installation position of the balance iron. Do not squeeze the handle when tightening the screws. The balance iron is slightly separated from the handle. If the installation position of the balance iron cannot be adjusted, please add a spacer between the balance iron and the handle. Excessive squeezing of the handle will cause difficulty in turning the handle switch and abnormal damage such as the heating wire squeezing out of the handle surface.
2. The product is equipped with high and low gear switches, and the handle temperature can be adjusted at will (50-70 degrees Celsius adjustable)
3. Double throttle cable buckle, wider installation range
4. The design can be sealed and can be opened, which will not affect the installation of the handle outside the handle, and then the lights and other decorative accessories are more beautiful and convenient
5. Input voltage: 12V
6. Power: 15W-35W adjustable
7. Length: left hand handle 143x36mm; right hand handle 127x36mm
Installation notes:
1. Remove the original handlebar
2. Use the left hand to moisten the inner hole with soapy water, and the twist should not be too large during installation
3. When installing the balance iron on the left hand handle, adjust the position of the balance iron to be slightly separated from the handle, and do not squeeze the handle when tightening the screw
4. If you use the left handle to slide on a steel pipe, remove the balance iron, and fix it with a few drops of 502 glue from the end of the handle
5. The power cord, the red wire is connected to the positive pole, and the black wire is connected to the negative pole, the temperature cannot be adjusted when reverse connection
6. When installing the left-hand handle, the power cord should be left enough for rotation
Precautions:
1. When installing the left handle, do not twist the handle too much. Excessive twisting will cause the heating wire to shift
2. For models with balance iron, please adjust the installation position of the balance iron. Do not squeeze the handle when tightening the screws. The balance iron is slightly separated from the handle. If the installation position of the balance iron cannot be adjusted, please add a spacer between the balance iron and the handle. Excessive squeezing of the handle will cause difficulty in turning the handle switch and abnormal damage such as the heating wire squeezing out of the handle surface.