XH-W3104 0-1000 High Power Digital Temperature Controller Thermocouple Temperature Control Switch
New
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 12 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Returns
Get it now, pay later
Seller
Buyer Protection
Product details
Condition
New
Location
International
Bob Shop ID
615107243
Specification:
Product Name: digital display temperature controller Product model: xh-w3104 Temperature measurement range: 0 ~ 1000 a?? Temperature measurement accuracy: ± 0.1 a?? Temperature control range: 0 ~ 1000 a?? Temperature control accuracy: 0.1 a?? Temperature probe: 1 m K-type thermocouple M6 thread probe Power supply voltage: AC220V 50hz Applicable environment: - 15 ~ 55 a?? / 20% ~ 85% RH Output type: AC220V direct output Dimension: 96 * 70 * 46mm Product weight: 214g
Package included:
1 x Digital Temperature Controller
P0 working mode:
1. Long press the setting button for more than 3 seconds to enter the internal menu and display P0, press the setting button again to proceed H (heating mode) / C (cooling mode) selection 2. Set stop temperature Short press the setting button to stop the temperature flashing, press the up/down button to adjust the stop temperature
P1 hysteresis setting: Long press the setting button for more than 3 seconds to enter the internal menu to display P0, press the up button to switch to P1, and press the set button again to set the return difference value Example: I want to control the temperature of the heating furnace to be heated between 340a??~350a??. How to set it? 1. Select the working mode as heating mode H 2. Set the stop temperature to 350a?? 3. Set the hysteresis to 10a?? and the setting is complete
P2 temperature correction: Long press the setting button for more than 3 seconds to enter the internal menu display P0, press the up button to switch to P2, and press the set button again to set the temperature correction value Example: The actual measured temperature is 100a??, and the thermostat displays 102a??. How to calibrate it? The temperature displayed by the thermostat is 2a?? higher than the actual measured temperature, just adjust the temperature correction value to -2
P3 high temperature alarm value: Long press SET?button??for more than 3 seconds to enter the internal menu display P0, press the up button to switch to P3, press the SET button again to set the high temperature alarm value The temperature value flickers during high temperature alarm, heating mode: stop output/cooling mode: start output
Product Name: digital display temperature controller Product model: xh-w3104 Temperature measurement range: 0 ~ 1000 a?? Temperature measurement accuracy: ± 0.1 a?? Temperature control range: 0 ~ 1000 a?? Temperature control accuracy: 0.1 a?? Temperature probe: 1 m K-type thermocouple M6 thread probe Power supply voltage: AC220V 50hz Applicable environment: - 15 ~ 55 a?? / 20% ~ 85% RH Output type: AC220V direct output Dimension: 96 * 70 * 46mm Product weight: 214g
Package included:
1 x Digital Temperature Controller
P0 working mode:
1. Long press the setting button for more than 3 seconds to enter the internal menu and display P0, press the setting button again to proceed H (heating mode) / C (cooling mode) selection 2. Set stop temperature Short press the setting button to stop the temperature flashing, press the up/down button to adjust the stop temperature
P1 hysteresis setting: Long press the setting button for more than 3 seconds to enter the internal menu to display P0, press the up button to switch to P1, and press the set button again to set the return difference value Example: I want to control the temperature of the heating furnace to be heated between 340a??~350a??. How to set it? 1. Select the working mode as heating mode H 2. Set the stop temperature to 350a?? 3. Set the hysteresis to 10a?? and the setting is complete
P2 temperature correction: Long press the setting button for more than 3 seconds to enter the internal menu display P0, press the up button to switch to P2, and press the set button again to set the temperature correction value Example: The actual measured temperature is 100a??, and the thermostat displays 102a??. How to calibrate it? The temperature displayed by the thermostat is 2a?? higher than the actual measured temperature, just adjust the temperature correction value to -2
P3 high temperature alarm value: Long press SET?button??for more than 3 seconds to enter the internal menu display P0, press the up button to switch to P3, press the SET button again to set the high temperature alarm value The temperature value flickers during high temperature alarm, heating mode: stop output/cooling mode: start output
