30.5*30.5mm MATEKSYS GNSS M9N-F4-3100 NEO-M9N GPS Module with Magnetic Compass RM3100 Support Suppor
New
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 15 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Returns
Get it now, pay later
Seller
Buyer Protection
Product details
Condition
New
Location
International
Bob Shop ID
615160158
Features: -M9N-F4 series is based on ArudPilotsa?? AP_Periph firmware,? It is a GNSS+COMPASS+BAROMETER+IMU peripheral with CAN/UAVCAN and UART/MSP interfaces, plus 4x spare UARTs, 1x I2C expansion bus for additional peripherals. -M9N-F4 uses multi-constellation GNSS powered by u-blox NEO-M9N , NEO-M9N is a concurrent GNSS receiver which can receive and track multiple GNSS systems. Owing to the multi-band RF front-end architecture all four major GNSS constellations, GPS,Galileo, GLONASS and BeiDou can be received concurrently. -M9N-F4-3100 integrates an industrial-grade compass PNI RM3100 which provides high resolution, low power consumption, no hysteresis, large dynamic range, and high sampling rates. -M9N-F4 series is not just a AP_Periph with full AHRS sensors. It can also work as a flight controller with 9 PWM outputs.
Specifications Brand:?MATEKSYS? Item Name:?MATEKSYS GNSS M9N-F4-3100 GPS Module GNSS u-blox NEO-M9N (GPS, GLONASS, Galileo and BeiDou) Magnetic Compass RM3100? (M9N-F4-3100) Barometer DPS310 IMU ICM20602 MCU STM32F405RGT6 MicroSD socket Patch GNSS Antenna 25*25*4mm 4x spare UARTs(1,2,3,5),? UART4 for onboard NEO-M9N 1x CAN, UAVCAN Protocol 8x PWM +1x 2812LED outputs 1x I2C, onboard DPS310 & QMC5883L(M9N-F4-5883) MicroUSB and DFU button Input voltage range: 4.5~5.3V (5V pad/pin) Power consumption: 120mA Operating Temperatures: -20~80 ?ﾣC M9N-F4-3100,? 36mm*36mm*12mm, 17.5g Mounting Hole Distance: 30.5*30.5mm
Firmwares ArduPilot AP_Periph: F405-MatekGPS ArduPilot Plane/Copter/Rover: MatekF405-CAN INav Target: MATEKF405CAN
Tips & warning on M9N-F4-3100, The 3 magnetic coils have little solder paste to avoid the excess to a??tilta?? them, resulting in some reading inaccuracies of the compass. Any strong impacts will definitely separate them, especially the a??tall coila?? Sen-Z-f.? Pls use this precision module with care. M9N-F4 series dona??t have 5V regulator built-in,? they must be powered by external 5V source(4.5~5.3V) over any 5V pad/pins.? Vbat pad supports battery voltage detection only.
Package Included: 1x M9N-F4-3100 2x JST-GH-4P to JST-GH-4P 20cm silicon wire 1x JST-SH-3P to JST-SH-3P 8cm silicon wire Mounting base (1x PCB plate,? 4x silicon grommets, 4x Nylon standoffs M3x7,? 4x Nylon screws M3*8)
Specifications Brand:?MATEKSYS? Item Name:?MATEKSYS GNSS M9N-F4-3100 GPS Module GNSS u-blox NEO-M9N (GPS, GLONASS, Galileo and BeiDou) Magnetic Compass RM3100? (M9N-F4-3100) Barometer DPS310 IMU ICM20602 MCU STM32F405RGT6 MicroSD socket Patch GNSS Antenna 25*25*4mm 4x spare UARTs(1,2,3,5),? UART4 for onboard NEO-M9N 1x CAN, UAVCAN Protocol 8x PWM +1x 2812LED outputs 1x I2C, onboard DPS310 & QMC5883L(M9N-F4-5883) MicroUSB and DFU button Input voltage range: 4.5~5.3V (5V pad/pin) Power consumption: 120mA Operating Temperatures: -20~80 ?ﾣC M9N-F4-3100,? 36mm*36mm*12mm, 17.5g Mounting Hole Distance: 30.5*30.5mm
Firmwares ArduPilot AP_Periph: F405-MatekGPS ArduPilot Plane/Copter/Rover: MatekF405-CAN INav Target: MATEKF405CAN
Tips & warning on M9N-F4-3100, The 3 magnetic coils have little solder paste to avoid the excess to a??tilta?? them, resulting in some reading inaccuracies of the compass. Any strong impacts will definitely separate them, especially the a??tall coila?? Sen-Z-f.? Pls use this precision module with care. M9N-F4 series dona??t have 5V regulator built-in,? they must be powered by external 5V source(4.5~5.3V) over any 5V pad/pins.? Vbat pad supports battery voltage detection only.
Package Included: 1x M9N-F4-3100 2x JST-GH-4P to JST-GH-4P 20cm silicon wire 1x JST-SH-3P to JST-SH-3P 8cm silicon wire Mounting base (1x PCB plate,? 4x silicon grommets, 4x Nylon standoffs M3x7,? 4x Nylon screws M3*8)
