This item has closed with no items sold
View the relisted Item
View the relisted Item
View other items offered by szulou1727
Geekcreit 433MHz DC12V 10A 1CH Single Channel Wireless Relay RF Remote Control Switch Receiver Boa
New
R395.00
Closed
11 May 24 00:05
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 15 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Returns
Get it now, pay later
Seller
Buyer Protection
Product details
Condition
New
Location
International
Bob Shop ID
612374540
Specification: ? 1. Input Voltage: DC10-14V 2. Standby Current: <5MA 3. RF Frequency: 433MHz 4. RF Working mode:Super heterodyne receiver 5. Receiver Sensitivity: >97dBm 6. Remote Control Distance: >100 meter(In open environment) 7. Decoding Way: MCU Software decoding 8. Can store the number of remote control:50 9. Support remote control type: Fixed code, learning code 10. Channel: 1CH 11. Multiple working modes: (Jog/Non-Latched ,inter-lock/Latched ,self-lock /Self-Latched,Delay off) 12. Wiring Method:Fixed wiring terminal 13. Working Voltage: DC12V 14. Output Current: 10A 15. Rated load:10A 250VAC / 10A 125VAC / 10A 30VDC / 10A 28VDC 16. Output:Normally open,Common,Normally closed 17. Dimension:3.5cmx3cmx1.8cm ? How to use: ? - Working/output way: 1.Jog/Non-Latched: Press one button is Working /ON. Loosen your finger on the same button is Stop/OFF. One channel switch need one buttons remote control. 2.Self -lock/Self-Latched: Press one button for one time is working/ON. Press the same button again is stop/OFF. One channel switch need one buttons remote control. 3.Inter-lock /Latched: Press one button is working/ON, press another button is stop/OFF. One channel switch need 2 buttons remote control. 4.Delay: Press remote control 's one button,relay is working,release the remote control and begin timekeeping,after 5s/10s/15s will automatically close the relay ? - Learn: 1. press the learning code .the indicator flash ,loosen your finger ,press any button of the remote control (press 1 times to learn Momentary;2times- Toggle;3times-Latched;4times-5s delay;5times-10s delay;6times-15s delay) the indicator flash 2 times and off .it mean you learn it successfully. 2. it can learn 2272 2262 or 1527 chip with the different code wireless 315MHz remote control ? - Reset new operating mode: 1. Jogging Press the white learning button on the top of the control panel, LED lights, and then press any button on the remote control set to 'Jog' button, the control panel LED lights flashing, indicating that the setup is complete 2. Self-locking Press the white learning button on the top of the control panel, LED lights, and then press any button on the remote control to set to 'self-locking' button, the control panel LED lights flashing, 3. Interlock Press the white learning button on the control panel, the LED lights, and then press any button on the remote control set to 'start' button, the control panel LED lights flashing, press another button to set to 'stop' button LED Blinking means the setting is complete ? - Remove/clean: Press the learning button about 8 seconds , the indicator turn on to off, it means the information that you keep have been removed successfully . ? Package included: ? 1 x 433MHz Switch Relay Receiver With Case
