This item has closed with no items sold
View the relisted Item
View the relisted Item
View other items offered by szulou1652
Similar products
Happymodel TeenyF3 Pro Flight Controller Built-in Betaflight OSD & Buck-Boost Converter for RC Drone
New
R655.00
Closed
11 May 24 00:16
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 15 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Buyer Protection
How you're covered
Get it now, pay later
Returns
Product information
Condition:
New
Location:
International
Bob Shop ID:
612417708
Happymodel TeenyF3 Pro Flight Controller Built-in Betaflight OSD & Buck-Boost Converter for RC Drone
Specification:
Brand name: happymodel
Item name:?TeenyF3 Pro flight controller
Size: 20*20mm
Mounting hole: 16*16mm
Diameter: 2mm
Weight: 2.1g
Processor: STM32F303CCT6 (72MHZ, 256K FLASH)
Sensor: MPU-6000 ( connected by SPI)
Firmware version: betaflight_3.1.7_OMNIBUS
Built-in Buck-Boost Converter
Receiver: PPM, Spektrum 1024/2048, SBUS, IBUS, XBUS, SumD SumH RX etc.
Power supply: 1S~2S lipo battery?
Suitable for 60mm-80mm mini brushless FPV frame
Features:
-Support programmable LED_Strip
-Support BLheli/BLHELI_S suite Pass-through ready
-Support PPM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300,? ? ?Dshot600
-Support the newest DSHOT ESC
-Built-in voltage detection, alarm
-Built-in Betaflight-OSD
-Buzzer solder pin
-LED_STRIP connector
-BB ring
Notes:
-DSM/DSM2/DSMX,SBUS,Ibus receiver input, please configure RX3(UART3) as input interface.
-DSM receiver power from 3.3V.
-SBUS and PPM receiver power from 5V.
Package included:
1* flight control board
1* cables(connection with Teeny1s 6a 4in1 esc)
4* M2*5+5 Nylon column
4* M2 Nuts
4* M2 Screw
Specification:
Brand name: happymodel
Item name:?TeenyF3 Pro flight controller
Size: 20*20mm
Mounting hole: 16*16mm
Diameter: 2mm
Weight: 2.1g
Processor: STM32F303CCT6 (72MHZ, 256K FLASH)
Sensor: MPU-6000 ( connected by SPI)
Firmware version: betaflight_3.1.7_OMNIBUS
Built-in Buck-Boost Converter
Receiver: PPM, Spektrum 1024/2048, SBUS, IBUS, XBUS, SumD SumH RX etc.
Power supply: 1S~2S lipo battery?
Suitable for 60mm-80mm mini brushless FPV frame
Features:
-Support programmable LED_Strip
-Support BLheli/BLHELI_S suite Pass-through ready
-Support PPM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300,? ? ?Dshot600
-Support the newest DSHOT ESC
-Built-in voltage detection, alarm
-Built-in Betaflight-OSD
-Buzzer solder pin
-LED_STRIP connector
-BB ring
Notes:
-DSM/DSM2/DSMX,SBUS,Ibus receiver input, please configure RX3(UART3) as input interface.
-DSM receiver power from 3.3V.
-SBUS and PPM receiver power from 5V.
Package included:
1* flight control board
1* cables(connection with Teeny1s 6a 4in1 esc)
4* M2*5+5 Nylon column
4* M2 Nuts
4* M2 Screw