3.3-5V 3-Wire Vibration Sensor Module Vibration Switch Alarm Module
New
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 15 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Returns
Get it now, pay later
Seller
Buyer Protection
Product details
Condition
New
Location
International
Bob Shop ID
615098868
Features:
? 1. Use all kinds of sensitivity vibration switch produced by our company, default SW-18015P vibration sensor. 2. Comparator output, clean signal, good waveform, strong driving ability, more than 15mA. 3. The working voltage: 3.3V to 5V 4. Output form: digital switch output (0 and 1) 5. Equipped with fixed bolt hole, easy to install 6. PCB board size: 3.2cm x 1.4cm 7. Use the LM393 wide voltage comparator ? Module interface description (3-wire):
1. VCC external 3.3V-5V voltage (can be directly connected with the 5V and 3.3V )
2. GND external GND
3. DO small board digital output interface (0 and 1) module instructions:
When the VCC and GND are connected, the module power indicator will light.
Put the module on the desktop, adjust the blue potentiometer on the board until the on-board switch indicator light, and then slightly callback potentiometer, so that the switch indicator light off, and then beat the desktop by hand, so that vibration sensor shock, the indicator light will go to the light state. Vibration stop, switch indicator light will be off. This phenomenon is that the vibration can trigger the module, so that the switch indicator light.
Module connection details: ? 1. The VCC: connect power positive 2. The GND: connect power negative 3. DO: digital signal output
? Application: ? It is used for all kinds of vibration triggering, theft alarm, intelligent car, electronic building block and so on. Please note that the trigger time is short when the small vibration is induced, not enough to drive the relay, according to some people can be directly connected to the relay module, and the actual effect is not good enough.
? Package included: ? 1 x Vibration sensor module
, 
, 
, 
? 1. Use all kinds of sensitivity vibration switch produced by our company, default SW-18015P vibration sensor. 2. Comparator output, clean signal, good waveform, strong driving ability, more than 15mA. 3. The working voltage: 3.3V to 5V 4. Output form: digital switch output (0 and 1) 5. Equipped with fixed bolt hole, easy to install 6. PCB board size: 3.2cm x 1.4cm 7. Use the LM393 wide voltage comparator ? Module interface description (3-wire):
1. VCC external 3.3V-5V voltage (can be directly connected with the 5V and 3.3V )
2. GND external GND
3. DO small board digital output interface (0 and 1) module instructions:
When the VCC and GND are connected, the module power indicator will light.
Put the module on the desktop, adjust the blue potentiometer on the board until the on-board switch indicator light, and then slightly callback potentiometer, so that the switch indicator light off, and then beat the desktop by hand, so that vibration sensor shock, the indicator light will go to the light state. Vibration stop, switch indicator light will be off. This phenomenon is that the vibration can trigger the module, so that the switch indicator light.
Module connection details: ? 1. The VCC: connect power positive 2. The GND: connect power negative 3. DO: digital signal output
? Application: ? It is used for all kinds of vibration triggering, theft alarm, intelligent car, electronic building block and so on. Please note that the trigger time is short when the small vibration is induced, not enough to drive the relay, according to some people can be directly connected to the relay module, and the actual effect is not good enough.
? Package included: ? 1 x Vibration sensor module
, , ,