This item has closed with no items sold
View the relisted Item
View the relisted Item
View other items offered by szulou1762
Similar products
Happymodel Crazybee F3 Flight Controller 4 IN 1 5A 1S Blheli_S ESC Compatible DSM2/DSMX Receiver for
New
R1,142.00
Closed
11 May 24 00:18
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 15 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Returns
Get it now, pay later
Seller
Buyer Protection
Product details
Condition
New
Location
International
Bob Shop ID
612428817
Happymodel Crazybee F3 Flight Controller UR65 US65 UK65 4 IN 1 5A 1S Blheli_S ESC Compatible DSM2/DSMX?
Crazybee F3 flight controller is a Ultimate version for 1S Whoop?brushless?racing drone, ita??s the world first Tiny whoop size brushless flight controller with Receiver/4in1 ESC/OSD/Current Meter all in one design, include all your needs .
?
Now the new version for DSM2/DSMX is coming
?
Specifications:
Firmware: Betaflight_3.5.0_Crazybee
MCU: STM32F303CCT6 (72MHZ, 256K FLASH)
Sensor: MPU-6000(SPI connection)
Power supply: 1S battery input (DC 3.5-4.35V)
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Serial-based Spektrum compatible DSM2/DSMX satellite receiver
Built-in Betaflight OSD(SPI Controll)
Built-in Current meter (Max 14A,could be modified to 28A by replace resistor)
Built-in 5V 0.8A BEC with LC filter
Built-in voltage detection
BLHELI_S pass-through Ready
Heading LED Ready
Board size: 28.5 * 28.5MM
Board weight: 3.5?g
ESC parameters:
Power supply: 1S LiPo/LiPo HV (4.2v/4.35v)
Current: 5A continuous peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: O_L_5_REV16_6.HEX
Signal Support: Dshot150/Dshot300/Dshot600/Oneshot125/Multishot/PWM
?
Receiver parameters:
Serial-based Spektrum DSM2/DSMX compatible Satellite?receiver
DSM2/DSMX compatible
Channels: 6ch~9ch(according to your transmitter)
Failsafe support
No ground interference ( Transmitting and receiving 1 m?from the ground): 300m
Package Included:
1 x Crazybee Flight Controller ESC DSM2/DSMX Receiver
DSM2/DSMX version receiver configuration:
Binding procedure:
(1) Connect Crazybee F3 DSM2/DSMX Version to computer and open Betaflight configurator, From CLI tab type: set spektrum_sat_bind = 9 for DSMX radio or set spektrum_sat_bind = 5 for DSM2 radio
(2) Type save and after Flight controller reboot remove USB cable (=Power off the board)
(3) Wait a second and reconnect the USB cable. After cold start satellite led?combo on the backside of the board (2 red led+2 white led) should start blinking and transmitter should be turned on while pressing the bind button
(4) After binding satellite led should be solid. Connect Betaflight and use receiver tab to test that satellite is working correctly.
(5) Final step is to go to CLI tab and type set spektrum_sat_bind = 0 and then type save. This must be done so that satellite doesn't go back to binding mode when the flight controller?is repowered again.
Crazybee F3 flight controller is a Ultimate version for 1S Whoop?brushless?racing drone, ita??s the world first Tiny whoop size brushless flight controller with Receiver/4in1 ESC/OSD/Current Meter all in one design, include all your needs .
?
Now the new version for DSM2/DSMX is coming
?
Specifications:
Firmware: Betaflight_3.5.0_Crazybee
MCU: STM32F303CCT6 (72MHZ, 256K FLASH)
Sensor: MPU-6000(SPI connection)
Power supply: 1S battery input (DC 3.5-4.35V)
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Serial-based Spektrum compatible DSM2/DSMX satellite receiver
Built-in Betaflight OSD(SPI Controll)
Built-in Current meter (Max 14A,could be modified to 28A by replace resistor)
Built-in 5V 0.8A BEC with LC filter
Built-in voltage detection
BLHELI_S pass-through Ready
Heading LED Ready
Board size: 28.5 * 28.5MM
Board weight: 3.5?g
ESC parameters:
Power supply: 1S LiPo/LiPo HV (4.2v/4.35v)
Current: 5A continuous peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: O_L_5_REV16_6.HEX
Signal Support: Dshot150/Dshot300/Dshot600/Oneshot125/Multishot/PWM
?
Receiver parameters:
Serial-based Spektrum DSM2/DSMX compatible Satellite?receiver
DSM2/DSMX compatible
Channels: 6ch~9ch(according to your transmitter)
Failsafe support
No ground interference ( Transmitting and receiving 1 m?from the ground): 300m
Package Included:
1 x Crazybee Flight Controller ESC DSM2/DSMX Receiver
DSM2/DSMX version receiver configuration:
Binding procedure:
(1) Connect Crazybee F3 DSM2/DSMX Version to computer and open Betaflight configurator, From CLI tab type: set spektrum_sat_bind = 9 for DSMX radio or set spektrum_sat_bind = 5 for DSM2 radio
(2) Type save and after Flight controller reboot remove USB cable (=Power off the board)
(3) Wait a second and reconnect the USB cable. After cold start satellite led?combo on the backside of the board (2 red led+2 white led) should start blinking and transmitter should be turned on while pressing the bind button
(4) After binding satellite led should be solid. Connect Betaflight and use receiver tab to test that satellite is working correctly.
(5) Final step is to go to CLI tab and type set spektrum_sat_bind = 0 and then type save. This must be done so that satellite doesn't go back to binding mode when the flight controller?is repowered again.