Maker Drive: Simplifying H-Bridge Motor Driver for Beginner
New
Indicative market price: R135.14
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Free collection from
Henley on Klip, Meyerton
The seller allows collection for this item and will be in contact with the full collection address once the order is ready.
Ready for collection by Thursday, 16 May.
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 2 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Get it now, pay later
Seller
Buyer Protection
Product details
Condition
New
Location
South Africa
Product code
2385
Bob Shop ID
613701366
Description:
For full instructions see our blog
Brushed motor is the most widely used motor because it is easy to use. Just supply the two terminals with DC power, the motor will start rotating! If you want to control its speed and direction using a controller, usually you will use an L298N Motor Driver. But if you want an easy and beginner-friendly motor driver, you are on the right page! Maker Drive is designed for simplicity and with the beginner in mind!
Motor Driver for Beginner- Maker Drive
Specifications:
What's in the box:
1 x Maker Drive board
Resources:
For full instructions see our blog
Brushed motor is the most widely used motor because it is easy to use. Just supply the two terminals with DC power, the motor will start rotating! If you want to control its speed and direction using a controller, usually you will use an L298N Motor Driver. But if you want an easy and beginner-friendly motor driver, you are on the right page! Maker Drive is designed for simplicity and with the beginner in mind!
Motor Driver for Beginner- Maker Drive
Maker Drive is not an Arduino Shield, but it is compatible with different models of Arduino main board such as:
- Maker UNO
- Arduino UNO R3
- Arduino Mega 2560
- Arduino Nano
- Arduino Pro Mini
- And the list goes on.....
Not to forget that it accepts 1.8V, 3.3V & 5V logic(for control) and is compatible with controllers such as Raspberry Pi, micro:bit, Raspberry Pi Pico, ESP etc.
Since you have Maker Drive, you will need suitable DC brushed motors besides the controller, right? So which motor is suitable for Maker Drive? Well, as long as the motor is...
- DC Brush motor (Two Terminals)
- Operating voltage from 2.5V to 9.5VDC
- Rated Current 1.0A
- Peak Current 1.5A
Example of suitable DC brush motor for Maker Drive (Not limit to):
- TT-02 DIY Car Model TT Motor w/ Wheel - Black Yellow
- 2WD Robot Car Chassis Kit single
These are the suggested power sources for Maker Drive:
- 2, 3 or 4 x AA/AAA batteries (2 x 1.5V = 3.0V) Battery holder
Specifications:
- Dual-channel, Bi-directional control motor driver
- Support motor voltage from 2.5V to 9.5VDC
- Maximum current up to 1.0A continuous and 1.5A peak (less than 5 seconds)
- 5V Output (200mA) to power the controller.
- Inputs compatible with 1.8V, 3.3V and 5V logic (Arduino, Raspberry Pi, etc).
- Solid-state components provide faster response time and eliminate the wear and tear of mechanical relay
- Regenerative Braking
- Speed control PWM frequency up to 20KHz (Actual output frequency is the same as input frequency)
- Dimension: 43mm(W) x 35mm (L) x 14mm (H)
What's in the box:
1 x Maker Drive board
Resources:
- Datasheet
- Note: Stock is currently available in South Africa for national shipping!